Blue Lagoon
PC-26
🟪 Purple Level
Blue Lagoon is a satin brush-on glaze from Amaco's Potter's Choice line, fired cone 5 to cone 6. Watery, cool, tidal.
SatinSemi-translucentTexture-friendlyCone 5/6
Available at The Clay HoleYes
Find it on the glazes shelves
Shelf 3, Row 2Tile #19 on the Potter's Choice pot
Show me where
Search results
Results
Friendly studio tip for this glaze
Save this one for a pot with deep carving. The pale pooling is the whole point, and it needs somewhere low to gather before it can do anything.
The quick version of Blue Lagoon
Stability/fluidityFluid, keep it off the foot
CoatsThree, applied heavy
TypeBrush-on glaze
FinishSatin
OpacitySemi-translucent
Shows textureYes, good on carving
Glaze fire toCone 5/6
Bisque toCone 04
DifficultyBeginner-friendly
What this glaze does
A cool blue that breaks milky green and then pools pale in the low spots, which is exactly the trick the name is describing: shallow water over sand, deeper water further out.
Applied heavily it floats, and the floating is where the surface variation comes from. On deep texture it separates into clear zones instead of a single flat blue.
How much it varies
The color is dependable. The pattern is not, because floating and pooling follow the form and the thickness rather than the brush.
Clays that suit Blue Lagoon
Semi-translucent, so the clay tone shows through a little at the thin end. On lighter clays the pale pooled areas read cooler; on darker bodies the whole glaze goes deeper.
Thirty three of these forty six glazes are opaque, so on most of them the clay underneath is a surface to sit on rather than part of the finished color. The other thirteen see through to some degree, and those are the ones where your clay choice really shows.
Rated forStoneware and porcelain at cone 5 and cone 6, which covers every body on our shelf.
Light bodies#16 Porcelain, B-Mix and Half & Half show these glazes closest to the test tile. Start here if you want the color on the label.
Buff bodies52 Buff and Speckled Buff run warmer and let iron specks come up where the glaze thins. On the see-through glazes that speckle is often what makes the pot.
Berlin GrayOur dark body, and the one that changes these glazes most. Anything see-through goes deeper and quieter on it.
Chasing pinholesAmaco reports this line clearing up on a smooth, low-grog body more often than not. Worth trying before you blame the glaze.
Applying this glaze to your work
Heavier coats are what make it float and vary. Three coats, not thinned. A light application flattens it into an ordinary pale blue.
How much it moves
Amaco calls it a fluid glaze. It moves, and it moves more where it is thick. Keep it off the foot.
Across the Potter's Choice line
Amaco's instruction for the line is three brush coats, not thinned, each one dry before the next. Their own guidance says most disappointing results come from glaze applied on the light side. Amaco publishes an application guide showing what too thin and too thick actually look like.
Layering
Its own float gives it plenty of activity, so it works as a finish. If you layer it, test a tile, because a fluid glaze under a fluid glaze compounds the running.
Before you commit a pot
Amaco's own combination tiles usually show two coats of each glaze, which lands four coats total anywhere the two overlap. Their standing advice is to test a tile before committing a piece, and to re-test when a new batch number arrives, since raw materials shift between production runs. Dipping versions of these glazes behave differently from the brushing jars and are much harder to layer.
From The Clay Hole University
More info about Blue Lagoon below, but first... Everything we teach about glazing, written down and taught properly. These are the glaze lessons, and they are a small corner of a library that runs from centering your first pot to selling your work.
GuideGlaze Brushing Techniques, Coat by Coat
GuideGlazing Big and Intricate Pottery Faster
GuideGetting the Most Out of the Mega Glaze Tool
GuideMaking, Logging and Dialing in Test Tiles
GuideGlaze Problems, Causes and Fixes
GuideGlazing on the Wheel for Even Coats and Clean Bands
GuideBubble Glaze with Dish Soap
GuideMixing Your Own Glazes: What It Actually Involves
GuideMaking a Glaze Catcher
GuideGetting Great Results with Crystalline Glazes
GuideOxide and Carbonate Washes
GuideWhen to Use Celadon Glazes
GuideHow to Use Dipping Glazes
RakuRaku Firing: Techniques, Tips and How It Works
UnderglazeHow to Use Underglaze: Techniques, Rules and Firing
UnderglazeMishima: How to Inlay Slip and Underglaze into Carved Lines
UnderglazeWipe-Away Texture: Underglaze and Oxide Washes on Bisque
Firing Blue Lagoon
Amaco rates the line for cone 5 and cone 6, published as 2167F and 2232F on a medium speed firing, over bisque fired to cone 04.
If you are a member here
None of this is yours to manage. We handle everything on the kiln side, and every glaze on our shelves can be fired safely in our studio.
Common problems with Blue Lagoon
Why is mine one flat blue with no variation?
Too thin. The floating and pooling only happen where enough glaze is present to move.
Why did it run down the pot?
It is fluid by design. Heavy coats plus a vertical wall equals travel. Stop it high.
What to put it on
Forms and surfaces
Deeply carved and textured work, where the pooling has somewhere to gather. Bowls read especially well because the pooling collects in the well.
Colors beside it
Blues and greens are already inside it, so it belongs beside sand tones, cream and warm neutrals rather than more blue.
Food and function
Amaco rates this glaze food safe and dinnerware safe, lead free and AP Non-Toxic. As a fluid glaze, keep it well clear of the foot on anything that has to sit flat on a table.
Across the Potter's Choice line
Every glaze in the line is lead free and, by Amaco's rating, dinnerware safe except PC-4 Palladium and PC-64 Aventurine. Amaco's own label carries the standard caution that anyone producing tableware should test finished ware, because firing temperature and contamination vary between kilns.
Our test tile pots
Every glaze family on our shelves has its own test tile pot, and it is the fastest way to decide what to put on a piece. It is a fired pot wearing the whole family, one numbered tile per glaze, on a surface built to show you what that glaze actually does rather than just what color it is.
- 1Find the pot The brand and family name are written on the rim. This glaze lives on the Amaco Potter's Choice pot.
- 2Find the tile This one is tile #19. The numbers match the ones in the Glaze Bible.
- 3Read it properly Look at what the glaze does across all four textures, not just what color it is.
What to look at on the tile
Broad vertical textureA broad open surface. Shows the color at full strength, and whether the glaze travels down it.
Shallow textureA shallow swirl stamp. Shows whether light carving still reads once the glaze is on, or fills in and vanishes.
Deep textureCut lines. A deeply rough texture stripe. Shows where the glaze pools, how it breaks, and how dark it goes in the recesses.
Wipe-away textureGlaze wiped back to bare clay. Shows what the edge does where the coat runs thin. Find this wiped away on the tile's number.
One trick worth knowing
Some glazes tell you loudly that they run. Others hide it. Look at how the brushed lines fired: crisp edges mean a stable glaze, and edges that went soft and fluid mean it moved, and it will move on your pot too.
Other glazes close to Blue Lagoon
Arctic Blue is the calm, stable version. Textured Turquoise leans green and moves similarly. Sapphire Float takes the floating idea into deeper blue.
Looks great paired with
Put these on the shelf beside it, or on the next pot in the same set.
About the Amaco Potter's Choice Family
Potter's Choice is the line Amaco built so an electric kiln could do what a gas kiln does. Released in 2004, it reaches for the depth of cone 10 reduction glazes at cone 5 and cone 6 in ordinary oxidation. That is the whole premise, and it is why the surfaces break, pool, float and shift instead of sitting flat.
It is one of the most layered brushing lines in American pottery, and Amaco keeps a public library of combination tiles for it. Most of the effects potters chase come from two of these glazes meeting on one pot.
Made by Amaco, a company that has been building glazes and kilns in Indianapolis since 1919. The Potter's Choice line arrived in 2004 and has been a reference point for mid-fire reduction looks since.
More ways to pick a glaze
Membership levels that may use this glaze: Purple & Black
Not sure whether this glaze suits what you are making, or how it works with our system here? Ask an instructor. That is what we are here for, and a two minute conversation at the shelf beats a fired pot you did not want.
About these images and what your pot will actually look like
We have done our best to represent every glaze here accurately, and you should still expect your pot to look different from what is on this screen.
Our glaze tile images are digitally created. They are built to show the character of a glaze, not to be a color match.
A screen is not a printout, a printout is not a test tile, and a test tile is not a finished pot. Each step in that chain shifts what a glaze looks like, sometimes a lot.
On top of that, the pottery itself changes the result: the clay body, how thick the glaze went on, whether it was brushed, dipped or sprayed, what was layered under or over it, where the piece sat in the kiln, how hot that spot ran, how fast it cooled, what was fired next to it, and how much texture the surface had. Two pots glazed from the same jar on the same day can come out different.
Treat every image here as a starting point, and treat a test tile fired on your own clay as the real answer.